Shimadzu LC-2010A HPLC System
Item ID:
Manufacturer
Condition
3-12 month warranty
Service options & contracts available
To sell, trade-in, or service your equipment
How do we Refurbish Lab Equipment?
Looking for further assistance? Contact Us
Request Quote/ Offer
Estimate Shipping Time
Canada & U.S.: 3-5 business days
International: 5-10 business days
Tariff-Free Shipping to the U.S.!
Solvent Delivery Pump (Degasser/mixer)
| Specification | |||
| Construction | Quaternary low pressure gradient | ||
| Pump type | Series double-plunger system (primary 10µ L, secondary 5µ L) | ||
| Solvent delivery system | Low flow rate delivery | ||
| Low flow rate delivery | Flow rate setting
range |
0.001µ 5 mL/minµ 1.0µ 35.0MPaµ | |
| Flow rate accuracy | (1% or (2µ L/min, below whichever is greater (1mL/min, 3.0 ~ 10.0MPa, water,
room temperature fixed at 20(C, except during gradient solvent delivery) (2% or (2µ L/min, below whichever is greater, except under above conditions (except in gradient solvent delivery) |
||
| Flow rate precision | 0.75%RSD or 0.02 min SD below whichever is greater
(0.05~2mL/min, 1.0 ~ 35.0MPa, methanol, room temperature fixed at 20(C) |
||
| Pressure limiter action | Maximum value / minimum value setting possible | ||
| Plunger, seal | Plunger: sapphire, seal: GFP | ||
| Check valves | 2 valves: inlet side is dynamic inlet valve (DIV) | ||
| Solvent switching | 4 solutions | ||
| Suction filter | 10µm | ||
| Line filter | 2µm | ||
| Drain valve | There is also an auto-drain manual valve, which uses a rotary valve injectionsyringe. | ||
| Pulsation | Less that 3MPa (3kg/cm2) (1mL/min of water, 100gk/cm2) | ||
| Pressure display accuracy | 2% or 0.5MPa, whichever is greater | ||
| Pressure sensor 0-point auto correction | Automatic zero adjustment upon instrument startup | ||
| Plunger rinse | Auto rinse function (standard) | ||
| Purge function | Auto Purge function, Manual Prime function | ||
| Gradient | No. of solvents mixed | 4 solutions | |
| Mixing ratio range | 0 ~ 100%, 0.1% steps | ||
| Concentration accuracy | (0.5% (0.1 ~ 2mL/min, 1.0 ~ 20.0MPa, water and aqueous acetone mixture) | ||
| Concentration precision | (0.1% (0.1 ~ 2mL/min, 1.0 ~ 20.0MPa, water and aqueous acetone mixture) | ||
| Mixer | Bowl mixer (270µ L) | ||
| Leak capacity | 800uL | ||
| Degasser | Membrane online degasser, 5 lines (4 mobile phase, 1 rinse solution) | ||
| Safety mechanism | Leak sensor | Detection of leaks at degasser, solvent delivery pump, UV-VIS detector | |
Autosampler
| Specification | |
| Injection system | Full volume sample injection, variable injection volume (zero sample loss during injection) |
| Injection volume setting range | 0.1 ~ 100µ L (standard), 1 ~ 2000µ L (option) |
| Number of samples processed | Model without sample cooler
350 (w/1mL sample vials), 210 (w/1.5mL sample vials, 100 (w/ 4mL sample vials), 384 (w/ 4 96-well microtiter plates), 1536 (w/ 4 384-well microtiter plates) 384 (w/4 96-well deepwell plates) |
| Sample vials | 1.5mL glass, 1.1mL glass, 1mL glass, 4mL glass, 0.3mL glass (w/plastic spacer), 0.3mL
glass (4mL vial storage type), 1mL plastic, 0.2mL plastic, 4mL plastic, 96-well microtiter plate, 384-well microtiter plate, 96-well deepwell |
| Injection volume repeatability | RSD<0.3% (10µ L injection) |
| Cross contamination | Less than 0.01% (using caffeine analysis conditions) |
| Injection volume accuracy | (1% (50µ L, n=6) |
| Injection time | 15 seconds |
| Number of repeat injections | 1 ~ 99 times/sample |
| Analysis time setting | 0.01 ~ 9999.9 minutes (0.1 min steps) |
| Number of injection parameterSteps | 202 steps max. |
| Sample suction speed | 0.1 ~ 15µ L/s ( 0.1µ L/s steps) |
| Rinse solution suction speed | 35 µ L/s |
| Applicable pressure | 35.0 MPa max. |
| Sample No. BCD output | Available (option) |
| Rinse solution degassing | Standard
|
Column Oven
| Specification | |
| Humidifying cooling system | Block heating system (mobile phase preheating function included) |
| Setting range | 4 ~ 60°C(1°C steps) |
| 4 ~ 60°C(1°C steps) | (1°C (when using block surface temperature at specified location, and set temperature of 50°C);
(1°C (when temperature of mobile phase coming from preheater and set temperature are 40°C, at 1mL/min); 3(°C) at full flow rate range, temperature range
|
| Temperature control precision | 0.1°C |
| Temperature control range | Room temperature -15°C ~ 60°C |
| Column oven interior Dimensions | Two 25cm columns
|
| Preision temperature control function | Preheater function, 2 flow lines
Capacity: 9µ L (conventional), 4µ L (semi micro) |
| Safety mechanisms | a) Maximum temperature setting to prevent overheating
b) Built-in temperature fuse c) Built-in leak sensor When leak sensor is activated, pump delivery, column oven termperature control, sample injection Stop |
| Time Program function | Controlled from system controller |
UV-Vis detector
| Specification | |
| Cell | Temperature control built-in
Cell length: 10mm, capacity: 8µL |
| Light source | Deuterium lamp |
| Wavelength range | 190 ~ 600mm |
| Spectral bandwidth | 8nm
|
| Wavelength precision | 1 nm |
| Wavelength repeatability | 0.1 nm |
| Drift | Less than 1 ( 10-4 AU/h(250nm, air in cell, fixed room temperature) |
| Noise level | (0.5 ( 10-5 AU (corresponding to response 2s, 250nm, air in cell) |
| Linearity | ~2.5Au |
| Auto wavelength accuracy check
Function |
Check using low pressure (voltage) Hg lamp at 253.7nm, D2 lamp 656.1nm |
| Check using low pressure (voltage) Hg lamp at 253.7nm, D2 lamp 656.1nm | Filter for absorbance check built-in |
| Response | 10 step switching using time 0.05,0.1,0.5,1.0,1.5,2.0,3.0,6.0,8.0,10.0 seconds |
| Range | From 0.0001-2.56 AUFS, 0.0001 AUFS step setting possible. |
| Zero correction | Auto zero function |
| Polarity switching | Possible
|
| Cell recognition function | Auto judgement of presence/absence of cell, cell type |
| Auto judgement of presence/absence of cell, cell type | 2 wavelength monitoring of either 190 ~ 390nm or 371 ~ 600nm |
| Time Program | Control from the controller possible |
| Output | Integrator output 0.5, 1, 2, 4, 1.25, 2.5 Au/V step switching |
System Controller
| Specification | |
| Display | Backlight equipped LCD display (320 ( 240 pixels), black and white |
| 3.5 inch floppy disk drive | Disk: 2HD, MS-DOS format |
| Input / output terminals | External inputs: 2, external outputs: 2
Optical link: 1 (for Chromatopac) RS-232C: 1 (for connection of PC) Analog output: 2ch |
| Units that can be connected | Recycle valve
BCD output option board (0-999 3-digit output possible) |
| Number of files | Method files: 20
System preparation files: 10 Shutdown files: 2 Sequence files: 1 |
This refurbished SHIMADZU LC-2010A HPLC SYSTEM is in great condition. It has been tested at SpectraLab Scientific.
A 90 day warranty is included.
People Also View
Related products
SpectraLab Scientific Inc
Established in 2003,
SpectraLab Scientific is a global leader of Refurbished analytical equipment. We specialize in reconditioning equipment, integrating the best available technologies from leading manufacturers across the industry. We are committed to quality and service, delivering strong customer satisfaction. We stock over 10,000 pre-owned lab equipment, components, and mix-and-match parts for your systems.
Our Services
Spectralab Scientific Inc. offers a variety of laboratory services to help you get started. Whether you’re setting up a new labs or developing your start up, we can help you overcome obstacles and provide turn-key solutions.
Repair Service
Parts and repairs for analytical equipment
Qualifications
IQ/OQ/PQ centered on compliance and data integrity
Service Contracts
Protect your lab and minimize downtime
Warranty
Up to 5 years warranty on most of the equipment
Installation & Training
Hassle-free setup & training from our professionals
Maintenance
Yearly PM to ensure peak performance